(1) Check the chain, sprocket, the more severe wear to be replaced. (2) Check the shaft axial and radial clearance, adjust or replace it. (3) whether each of the oil flow. (4) Remove all the protective cover, clear the obstruction. (5) The rotating parts filling oil, the remaining parts of oiled rust. Touching each rotating parts 11. When driving is prohibited. 12. In the transport, the wheels should be supported and fixed firmly locked; and lift the pickup mechanism, a certain distance away from the bottom pallet. 13. Action If overload stall, should immediately pulled hand clutch, the clutch state of separation, and then release the starter machine. If the two machines fail should immediately start opening the bundle. Otherwise, serious damage to the machine parts and motors. 14. Every half hour of work, should be removed once the machine crushed beneath the feed roll is less than expected, which brought in order to reduce the resistance. But also reduces the wear of the lower portion of the aluminum roller. Eight, Faults, causes and troubleshooting. See Schedule 3 failures may be due to the occurrence of the main transmission mechanism to resolve 1. abnormal noise roller bearing broken or worn chain roller chain sprocket adverse identify the cause of damage, replace the bearing adjustment Tensioner Sprockets are related sprocket Replace the chain on the same plane (or replace broken link) 2. winding mechanism abnormal noise chain, sprocket bad winding slide card master regulator Tensioner repair or replace the chain sprocket skateboard rails, filling oil feed conveyor 3 poor forage grass running track stuffed dead belt is too loose bearing damage caused by skidding trajectory to clear obstructions forage replacement belt replacement roller bearing 4. forage rotation is not flexible winding roller gap between two adjacent curved touch squeeze roller bearing wear Clear obstructions or broken (note activity siding) repair or replacement of straightening rollers, new shaft bearing 5. Replace the bad new baling wire feed line state Tarantino cramping real bad and insufficient forage bales have been sent to the next thread is not Again feed fine linen twine diameter or diameter replace bad wheel damping adjustment should feed again, again roping 6. Bundled compactness enough low speed damping roller wheel clamp loose feeding enough, uneven increase speed, Check the belt and tighten the wheel to adjust the damping full feeding, the last should be uniform, a small amount of feed 7. The opening and closing positions opening bad extension spring, tension adjustment clamping force opening hooks elastic tension spring tension adjustment screw hooks and stalls circle 8. The thickness of the grass bale barn Kun no grass density is too high humidity is too high rollers do not rotate the roller tray does not adjust the tilt angle damping wheel clamping wing nut, decrease the density Liangshai forage drove a warehouse adjust the height of the fixed support 9. sprocket engages bad sprockets, chain tensioner badly worn too loose or too tight often overloaded car, chain elongation replace the chain, sprocket wheel adjustment replace the chain tensioner wheel to adjust the damping of the machine in accordance with standard operating nine, machine environment (1) After the rigorous training of qualified operatives before using the machine. (2) This machine uses only three strands of coarse yellow rope (diameter ￠ 3mm). (3) the ambient temperature is less than zero Celsius 2 ℃, not allowed to use this machine. (4) Straw and forage moisture is greater than 65%, are not allowed to use this machine. (5) never allows the operator side bale, while on the machine to punch poured sterile water and other liquids. (6) does not allow two times per hour stuffy car phenomenon. (7) When using the motor for power, you must install the ground wire. (8) must be cleared up under the machine, both ends of the aluminum rollers and pick up the broken rear feeder is less than expected. Such as particle more about twenty bales per dozen clean up once; otherwise serious damage to the machine parts. (9) anomalies arise during operation of the machine, the user should promptly contact your local dealer or manufacturer. Never allow the user to disassemble the machine, but the machine does not allow unauthorized alteration, or peril. (10) the machine during use or storage, must be prepared to water, rain, rust treatment. The machine under normal conditions of use, production within five thousand packets, if there is damage to the parts, the Company had no taste of replacement parts, free services; five thousand packets received only part of the Company other than the cost of fees, and lifetime service.